AML M3000 Guía de usuario Pagina 117
- Pagina / 156
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
M3000 Portable Bar Code Reader User's Guide
9-2
Message Cause Solution
Transmit Error
Indicates that the transmit
communications aborted with an error.
Retry communications.
User Abort
A key was pressed on the M3000,
causing an abort.
Decrease baud rate.
Wedge Cable Is
Not Connected
The keyboard wedge cable is not
connected when trying to do a keyboard
wedge upload.
Check cables and check transmit setup
parameters.
Xmodem Error
Unable to connect using XMODEM
protocol.
Check cables and check transmit setup
parameters.
Bar Code Data Errors
Bar Code Is Too
Long For Input
Bar code has more characters than
allowed by maximum input size
specification.
Scan correct size bar codes or midify
input size in the program.
Bar Code Is Too
Short For Input
Bar code has fewer characters than
allowed by minimum input size
specification.
Scan correct size bar codes or midify
input size in the program.
Invalid Bar Code
Data For Input
Bar code data does not match the
current input's data specifications
Scan correct bar codes or modify input
data specifications in the program.
Invalid
Bar Code Type
Scanned bar code does not match
acceptable bar code types specified for
the current input.
Scan correct bar codes or modify bar code
types in the program.
Function Recall Errors
Recall Buffer
Is Empty
No information has been stored using
FUNC + STORE.
Enter data and save for
FUNC + RECALL
Recall Data Not
Valid For Input
RECALL data does not match the
current input's data specifications.
Modify recall data or change input data
specifications in the program.
Recall Data Too
Large For Input
Contents of RECALL buffer exceed
maximum input size specification.
Modify recall data or change input size in
the program.
Miscellaneous Errors
*END OF FILE*
No More Inputs
End of defined program inputs has
been reached.
None.
Battery Low
Press Any Key
Battery low detected. Replace 9V Alkaline battery.
Clock Error
No Response
Real Time Clock is not responding. Call for service.
External Ram
Error
M3000 has detected an external RAM
error.
Call for service.
FATAL FILE ERROR
M3000 has detected an un-recoverable
file error.
None
FILE ERROR
M3000 has detected a file error and will
attempt to repair file contents
None
Input Is Full
Cannot Insert
Maximum input size specification has
been reached, and will not allow
additional characters.
Press INS key to exit out of the insert
mode.
- User's Guide 1
- Contents 3
- Programming 5-1 4
- Setup Procedures 6-1 5
- Communications 7-1 8
- Advanced Operations 8-1 8
- M3000 Programmer 9-1 9
- Troubleshooting 10-1 9
- Specifications 11-1 9
- Maintenance 12-1 9
- Appendixes A-1 10
- Overview 11
- Portable Mode 12
- Non Portable Modes 12
- Communications 12
- Symbols: 13
- 1Installation 14
- Keyboard Wedge Installation 15
- Caution: 15
- Serial Wedge Installation 16
- RS-232 Serial Installation 16
- Modem Installation 18
- Installing Input Devices 18
- 2Keyboard 19
- Keyboard Layout 20
- Other Key Combinations 21
- 3Function Reference 22
- ATA FILES 23
- OOKUP FILES 24
- Search Text 26
- Startup - Portable Mode 28
- Using the INPUT Function 30
- Edit/Review a Data File 33
- Startup - Non Portable Mode 34
- Keyboard Wedge Mode 35
- Serial Wedge Mode 35
- RS-232 Serial Mode 36
- Nonportable Mode 37
- ➨RS232 SERIAL 37
- RS232 Serial 37
- Scanning Bar Codes 38
- CCD Scanning 41
- Slot Reader (Badge Reader) 42
- 5Programming 43
- Erasing a Program 44
- Exiting a Program 44
- Programming Tutorial 45
- EOF (End of File) Parameters 46
- Use Receive Data Files Only? 46
- Output Prefix 49
- Output Suffix 49
- Input Type 49
- Screen Positioning 50
- Input Size 50
- Input Controls 50
- Display Pattern 50
- Input Mask 50
- Input Definition # 5 52
- End of Program 53
- Stamp Commands 53
- ITEM NUMBER 54
- LOC (Location) 55
- UOM (Unit of Measure) 55
- DESCRIPTION 55
- *P6 (No Prompt) 55
- Creating a New Program 56
- SOF Text 57
- SOF Delay 57
- EOF Text 57
- EOF Delay 57
- Allow Append to End of File? 58
- Header Input? 58
- New Screen? 58
- Sample Prompt Text 59
- Enter Spaces Here 59
- Exhibit Text is not required 60
- Str Row 61
- Str Col 61
- End Row 61
- End Col 61
- Screen Specifications: 62
- Data Input Parameters 63
- Input Size Max 63
- Input Size Min 63
- Require Input? 63
- Auto Advance? 63
- Input Source K, B, S, or X 65
- Bar Code Types 65
- Bar Code Types is required 66
- Default Data is not required 66
- Prefix is 67
- Prefix is not required 68
- Prefix Delay is required 68
- Suffix is not required 68
- 6Setup Procedures 69
- Cursor Function 70
- Auto Advance 72
- ON/OFF* 72
- Setup Categories 75
- Keyboard Wedge 76
- Serial Wedge 76
- RS232 Serial 76
- Serial Port 78
- Bar Codes 81
- UPC/EAN Addons (SUPPLEMENTS) 83
- I 2 OF 5 83
- CODABAR 84
- CODE 128 84
- CODE 93 85
- MSI/Plessey 85
- Code 11 86
- Termination Character 86
- Preamble 87
- Postamble 87
- Bar Code Edit 87
- Bar Code Beeper 88
- Laser/CCD Opts (Options) 88
- Transmit Setup 89
- Num Lock 92
- SOT Text (Start of Transmit) 92
- SOT Delay 92
- EOT Text (End of Transmit) 92
- Other Setup 93
- Reset Setups 94
- 7Communications 95
- Communication Software 98
- FUNC + XMIT 99
- Transmit Select 99
- PCOM COMMUNICATION SOFTWARE 100
- SOFTCOM Kill Program 101
- Using SOFTCOM 102
- 8Advanced Operations 106
- Lookup Table Definition 107
- Simple Lookup File 107
- Lookup Tbl/File 108
- Lookup File Definition 109
- Lookup File with Display 109
- Creating the ASCII Data File 110
- Importing an ASCII Data File 113
- Other Advanced Options 114
- Input Source 115
- K,B,S or X: S 115
- Transmit Paused 115
- Press Any Key 115
- 9Troubleshooting 116
- Bar Code Data Errors 117
- Function Recall Errors 117
- Miscellaneous Errors 117
- Function Search Errors 119
- Serial Input Error Messages 119
- Troubleshooting Guide 120
- 10Specifications 121
- Battery Performance 122
- Input/Output Specifications 122
- 11Maintenance 126
- Dimple on This 127
- End of EPROM 127
- Avoiding Damage 128
- 12Maintenance 129
- Appendixes 132
- FUNCTION KEYS 133
- SPECIAL KEYS 133
- UPC VERSION A 137
- UPC-A BAR CODE 137
- UPC VERSION E 138
- 0123456789 139
- A123456B 141
- 0000123455555555558 142
- CHARACTER SET: 143
- CHARACTERISTICS 145
- CHARACTER SET 145
- 012345678 146
- APPENDIX L 151
- APPENDIX M 151
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales